1370 Vertical Machining Center – 15 kW Standard, 11 kW Low-Speed Option and 55-Series Guideways | BONANZA CNC

November 15, 2026 · bonanza_admin

1370 Vertical Machining Center: 15 kW Standard, an 11 kW Low-Speed Option, and 55-Series Guideways

Most buyers comparing machines in the 1300 mm X class read the travel figures first and stop there. Travel tells you whether the part fits. It does not tell you whether the machine can take the cut. On the 1370, the numbers that decide the second question are the two spindle motor options and the size of the linear guideways underneath the table.

The 1370 is a 9,000 kg vertical machining center with 1,300 / 700 / 750 mm travels, a BT40-150 spindle turning 8,000 rpm, and a 1,400 × 700 mm table rated for 800 kg. Below is what each of those figures changes on the floor.

What the 1,300 × 700 × 750 mm envelope actually covers

The table is 1,400 mm long and the X travel is 1,300 mm, so the table overhangs the saddle by 50 mm at each end. That margin is where your clamps and vises live. A 1,300 mm long workpiece clamped at both ends will not reach full X travel without repositioning, so plan for a tombstone or a second setup on parts longer than roughly 1,150 mm.

Y is a different story. The table is 700 mm wide and Y travel is also 700 mm, which means the table edge sits flush with the travel limit. Clamping a part tight to the front edge and then cutting at full Y positive will pull the part out from under the spindle. Keep the work zone inside 600 mm of Y if you want to use the full stroke.

Z at 750 mm is the figure that surprises people. With a 700 mm Y table, a tall fixture such as an angle plate, a rotary table on a riser, or a welding-style positioner still leaves clearance for a 200 mm tool hanging out of the spindle. Machines in this size class often ship with 600 to 650 mm of Z; the extra 100 mm is what lets you keep a fourth-axis unit mounted permanently instead of stripping it off between jobs.

Two spindle motor options on one frame

BONANZA publishes two motor configurations for the 1370: a 15 kW standard motor, or an 11 kW low-speed high-torque motor. The second one is not a downgrade. It is a different torque curve.

Power in kilowatts is a product of torque and speed. A 15 kW motor reaches its rating high in the rpm band, which suits aluminium, brass, plastics, and light finishing passes in steel where the spindle runs fast and the chip load is small. An 11 kW low-speed high-torque motor trades top-end power for torque at the bottom of the range. That is the zone where you tap M16 in 1045, run a 50 mm indexable drill, or take a 4 mm depth-of-cut roughing pass with a face mill at 600 rpm. Same spindle, same BT40-150 taper, different behaviour below 1,500 rpm.

If your work is 70% aluminium fixtures and 30% mild steel brackets, order the 15 kW. If it is hydraulic manifolds, mould bases, or anything where the cycle is dominated by removing cubic inches of steel at low speed, the 11 kW low-speed motor will finish the part faster than the bigger nameplate would.

55-series guideways and the ribbed bed

The 1370 runs 55-series linear guideways on all three axes. Rail width drives static load capacity and, just as importantly, damping. A wider rail carries more bearing blocks in contact with the raceway, so interrupted cuts such as milling a keyway, crossing a port, or breaking through a casting skin deflect the head less than a 35 or 45 series rail would on the same frame.

The bed casting uses what BONANZA describes as “meter”-shaped reinforcement ribs. In practice this is a grid of ribs running both across and along the casting rather than one direction only, which raises the natural frequency of the bed and keeps the mass where the load path is. At 9,000 kg against the 855D’s 5,300 kg, the 1370 carries about 70% more iron for a table that is 78% larger in area. The mass tracks the table size rather than lagging behind it, which is the point. That ratio is the reason the machine holds a finish pass on a part clamped at the far end of the table.

Rapid rates: 24 / 24 / 18 m/min

X and Y rapid at 24 m/min, Z at 18 m/min. The Z axis is slower because it carries the whole head assembly, and slowing Z is cheaper than adding counterbalance mass. For cycle-time estimates: a full X traverse of 1,300 mm takes about 3.3 seconds at 24 m/min, and a full Z drop of 750 mm takes 2.5 seconds at 18 m/min. On a part with 40 tool changes, the Z figure is the one that shows up in the cycle time, not X.

1370 published specification

Parameter VMC1370
Table size 1,400 × 700 mm
Max. worktable load 800 kg
T-slot (number × width × pitch) 5 × 18 × 130 mm
X / Y / Z travel 1,300 / 700 / 750 mm
X / Y rapid traverse 24 m/min
Z rapid traverse 18 m/min
Spindle taper BT40-150
Spindle speed 8,000 rpm
Spindle motor 15 kW standard, or 11 kW low-speed high-torque
Guideways 55-series, three axes
Machine dimensions 3,550 × 2,730 × 2,620 mm
Machine weight 9,000 kg

Where the 1370 stops and the next model starts

If your parts are long and narrow, such as base plates, linear rail beds, or extruded profiles, the 1560 gives you 1,500 mm of X on a 2,200 × 600 mm table and a 1,500 kg load rating, at the cost of 650 mm of Y and Z travel.

If the cut is heavy rather than long, the step up is the L1690, which carries a BT50-190 spindle at 6,000 rpm, a 1,600 × 800 mm table, and 900 mm of Y travel. BT50 tooling at 6,000 rpm is a different class of metal removal from BT40 at 8,000 rpm.

If you need the 1370 envelope with a specific Z requirement, the 1370D shares the same published travels and table dimensions, so the choice between them comes down to the column and head configuration rather than capacity.

Four checks before you send a part drawing

First, add your fixture height to the part height and confirm the total is under 750 mm of Z minus tool length. Second, weigh the part plus the fixture — 800 kg is a table rating, not a part rating. Third, count how many minutes of the cycle are spent below 1,500 rpm; that is the number that decides between the two motors. Fourth, check the door opening and the crane hook height against the 2,620 mm machine height, because a 9,000 kg machine does not get moved again once it is levelled.

The full specification and machine photographs are on the 1370 vertical machining center page, and the rest of the range is listed under vertical machining centers. Send a drawing with the fixture and the material and we will come back with the motor option and the tooling list.