
Pallet size is the first thing most buyers sort a horizontal machining center by, and it is the least useful number on its own. A 630 mm pallet and a 1600 mm pallet are not the same machine scaled up. The load rating, the travel you get past the pallet edge, and the spindle speed band all move in different directions as the pallet grows.
This is a reading guide to the eight BONANZA horizontal models, using published figures only. The TH1000S is a good place to start because it sits in the middle and breaks two of the usual assumptions.
Load per pallet area, not load per machine
A 4,000 kg rating on a 1000 mm pallet is 4,000 kg per square metre. The same rating on a 1600 mm pallet would be 2,500 kg per square metre — a much lighter duty part. Divide the load rating by pallet area and the range sorts itself out:
| Model | Pallet | Max. load | Load per m² of pallet |
|---|---|---|---|
| HTMC630-VI | 630 × 630 mm | 500 kg | ~1,260 kg/m² |
| 630-DT / HMC630II-ZT | 630 × 630 mm | 1200 kg | ~3,000 kg/m² |
| TH500 | 1200 × 600 mm | 800 kg | ~1,110 kg/m² |
| 800S-DT | 800 × 800 mm | 2000 kg | ~3,125 kg/m² |
| 800-DT | 800 × 800 mm | 2500 kg | ~3,900 kg/m² |
| TH1000 | 1000 × 1000 mm | 3500 kg | 3,500 kg/m² |
| TH1000S / 1000S-DT | 1000 × 1000 mm | 4000 kg | 4,000 kg/m² |
| TH1400S | 1400 × 1400 mm | 5000 kg | ~2,550 kg/m² |
| TH1600S | 1600 × 1600 mm | 10000 kg | ~3,900 kg/m² |
Two things fall out of that column. The TH1000S carries the highest load density in the range at 4,000 kg/m², on the same 1 m² pallet as the TH1000. And the biggest machine is not the heaviest-loaded per unit area — the TH1600S matches the 800-DT at roughly 3,900 kg/m². If your parts are large but not dense, a 1600 mm pallet is not automatically the right answer; you may be paying for floor space you do not use.
X travel minus pallet width is your overhang budget
Subtract pallet width from X travel and you get how far a workpiece can hang off the pallet edge and still reach the tool. It is the number that decides whether a long weldment or a shaft housing can be machined in one setup, and BONANZA machines are not consistent about it:
- TH1000S / 1000S-DT: 1800 mm travel − 1000 mm pallet = 800 mm of overhang
- 800-DT and 800S-DT: 1300 − 800 = 500 mm
- 630-DT, HMC630II-ZT: 1100 − 630 = 470 mm
- TH1400S and TH1600S: 1800 − 1400 and 2000 − 1600 = 400 mm each
- TH1000: 1300 − 1000 = 300 mm
- TH500: 1100 − 1200 = −100 mm, the table is longer than the X travel
The TH1000S gives up 400 mm of pallet width against the TH1400S and gains 400 mm of overhang in return. For long parts — base frames, machine beds, extruded profiles — that trade is usually worth more than the extra pallet area.
More cast iron does not mean more load rating
Compare the two 1000 mm machines. The TH1000 weighs 18,000 kg and takes 3,500 kg on the table. The TH1000S weighs 16,000 kg and takes 4,000 kg. The lighter machine is rated for the heavier part.
The same pattern shows up at 800 mm: the 800-DT is 16,000 kg for a 2,500 kg load, the 800S-DT is 15,500 kg for 2,000 kg. The extra mass in each case sits in the frame and the guideway structure, not in the load path. That is a deliberate choice about what kind of cutting the machine is for, not a specification error.
Read it as a hint about duty. A heavier frame with a lower load rating is built around rigidity for hard, interrupted cutting at moderate part weight. A lighter frame with a higher load rating is built to move bigger parts through the envelope quickly. Ask which one your part mix actually needs before comparing the two weight figures side by side.
Spindle speed drops as the pallet grows
Across the range, top spindle speed falls in a straight line: 6000 rpm at 630 and 800 mm, 6000 rpm on the TH1000, then 3000 rpm on the TH1000S, 2000 rpm on the TH1400S and 1500 rpm on the TH1600S. This is not a cost compromise. Big pallets carry big parts and big tools, and a 100 mm boring bar or a 160 mm face mill does not want to spin at 6000 rpm.
The TH1000S also changes taper designation: BT50-45° rather than the BT50 Φ190 used on the 630-DT and the TH1000. Both are BT50, and both run in the low-speed, high-torque band that box and valve work needs. The distinction matters when you specify tooling holders, so confirm it against the machine you order rather than assuming all BT50 tooling interchanges across the range.
Two versions of the same 1000 mm envelope
TH1000S and 1000S-DT share the identical working envelope: 1000 × 1000 mm pallet, 4000 kg, 1800/1000/1300 mm travels, 14/12/14 m/min rapids, 16,000 kg. The difference is on the table surface. The TH1000S uses 7 T-slots at 125 mm pitch; the 1000S-DT uses 5 T-slots at 160 mm pitch.
Wider pitch suits large tombstone fixtures and dedicated pallets with fewer, heavier clamps. Tighter pitch suits smaller fixtures repositioned often. If you are building fixtures in-house for a fixed family of parts, the 160 mm pattern gives you more room between clamps; if the machine will run mixed work on standard plates, the 7-slot layout is more flexible.
TH1000S specifications
| Parameter | TH1000S |
|---|---|
| Table size | 1000 × 1000 mm |
| Max. worktable load | 4000 kg |
| T-slot (number × width × pitch) | 7-22-125 mm |
| X-axis travel | 1800 mm |
| Y-axis travel | 1000 mm |
| Z-axis travel | 1300 mm |
| X-axis rapid traverse | 14 m/min |
| Y-axis rapid traverse | 12 m/min |
| Z-axis rapid traverse | 14 m/min |
| Spindle taper hole | BT50-45° |
| Spindle speed | 3000 rpm |
| Machine weight | 16,000 kg |
Where the other models fit
The TH1000 is the 18,000 kg, 6000 rpm alternative on the same pallet, and it can be ordered on a boring and milling, positive T, or inverted T structure. The TH1400S moves to a 1400 mm pallet with 5000 kg and a 1500 mm Z travel. The TH1600S is the top of the range at 10,000 kg and 24,000 kg of machine weight. At the lower end, the 800-DT keeps a reserved interface for a pallet changer, and the TH500 is the only BT40 model in the series at 7,200 kg with 24 m/min rapids.
Three checks before you request a quote
Weigh the fixture, not just the part. A 4000 kg rating includes the tombstone, the clamps and the hydraulic lines. A 900 kg fixture on a 3,500 kg part leaves very little margin.
Measure the longest dimension against overhang, not against pallet size. The TH1000S reaches 800 mm past the pallet edge; a 300 mm machine will not, whatever the pallet says.
Check the floor. The TH1600S is 24,000 kg, and the TH1000S is 16,000 kg on a footprint that is smaller than its mass suggests. A suspended slab needs a load rating check before delivery, not after.
Send us the part drawing, the fixture weight and the batch size. We will tell you which pallet size and which frame the job actually needs.
Request a TH1000S quote or browse the full horizontal machining center series.